首页 > 产品配件 > 详细信息
产品名称: 发动机喷油器#58832650
产品介绍:

 ①检查开启压力在专用喷油器压力试验器上测试喷油器开启压力,数值不得低于25.0+8.0Mpa;对于达不到此喷油压力的喷油器应进行清洗或酌情更换。

②检查是否滴油用干净的压缩空气吹干(或用干净抹布抹干净)喷油器表面,在喷油器试验器上将压力达到比开启压力低2.0MPa的压力下保持10秒钟,没有滴油现象,说明此喷油器可以继续使用。如果滴油,则必须维修,如果维修后情况没有改变,则必须更换系的喷油器。

③喷油器的安装要求BFM1013柴油机喷油器的安装容易出现180°的方向误差,因此在安装该柴油机的喷油器时应特别注意。该柴油机喷油器的回油管必须朝向柴油机的排气管一侧。

已就是当面朝单体泵安装孔时,喷油器的回油管朝向对面。如果安装方向错位180°,柴油机仍然可以起动,但可能会黑烟滚滚,运行时间长了还将导致活塞烧顶等严重故障。

 

 

免责声明丨 部分内容来源网络!本文仅供交流学习 , 版权归属原作者,部分图片、内容推送时未能及时与原作者取得联系,若来源标注错误或侵犯到您的权益烦请告知,我们将立即删除.


企业介绍

公司供应摊铺机配件,压路机配件,铣刨机配件,摊铺机刮板驱动轴,刮板驱动轴总成,找平仪,找平仪支架以及液压泵和配件。我厂还供应摊铺机易损件,摊铺机平衡梁,搅龙轴,踏板,输料底板,叶片,熨平板,减速机,链轨,履带板,支重轮,刮板大链条,输料链条等。


联系人:梁经理

联系方式:13645201509

(微信同号)

QQ:2870202745

① Check the opening pressure. Test the opening pressure of the fuel injector on the special fuel injector pressure tester, and the value shall not be less than 25.0+8.0Mpa; The fuel injectors that cannot reach the injection pressure should be cleaned or replaced as appropriate.

② Check whether the fuel injector surface is dripped with clean compressed air (or wiped clean with a clean rag), and keep the pressure at 2.0MPa lower than the opening pressure for 10 seconds on the fuel injector tester. There is no oil dripping, indicating that the fuel injector can continue to be used. If the oil drips, it must be repaired. If the condition does not change after the repair, the fuel injector of the system must be replaced.

③ The installation of fuel injector requires that the installation of fuel injector of BFM1013 diesel engine is prone to 180 ° direction error, so special attention should be paid when installing the fuel injector of this diesel engine. The fuel return pipe of the diesel fuel injector must face the exhaust pipe side of the diesel engine.

That is, when facing the unit pump mounting hole, the fuel return pipe of the fuel injector faces the opposite side. If the installation direction is misaligned by 180 °, the diesel engine can still be started, but the black smoke may billow, and the long operation time will also lead to serious faults such as piston burning.

Disclaimer | Part of the content comes from the network! This article is only for exchange and learning. The copyright belongs to the original author. Some pictures and content are not timely contacted with the original author when being pushed. If the source label is incorrect or infringes your rights and interests, please inform us and we will delete it immediately

Enterprise introduction

The company supplies paver parts, roller parts, milling machine parts, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument support, hydraulic pump and accessories. Our factory also supplies vulnerable parts of pavers, paver balance beams, auger shafts, pedals, feeding soleplates, blades, screeds, reducers, chain tracks, track shoes, rollers, scraper large chains, feeding chains, etc.

Contact: Manager Liang

Contact: 13645201509

(WeChat with the same number)

QQ:2870202745

 

 

免责声明: 本页产品如有侵权请联系我们进行删除处理!联系电话:18705218934
联系地址:徐州市矿山路枫林绿洲南门 邮编:221000
 联系电话:13645201509 QQ:2870202745  企业邮箱:audelo@163.com
版权所有 技术支持:徐州奥德隆工程机械有限公司 徐州德道网络科技有限公司
苏ICP备08022494号